- 您现在的位置：买卖IC网 > Sheet目录509 > SI4355-B1A-FM (Silicon Laboratories Inc)IC EZRADIO FM RECEIVER SI4355
Si4355
4.2.3. Frequency Deviation
If FSK or GFSK modulation is selected, then a frequency deviation will also need to be selected. The frequency
deviation is the maximum instantaneous difference between the FM modulated frequency and the nominal carrier
frequency. The Si4455 can operate across a wide range of data rates and frequency deviations. If a frequency
deviation needs to be selected, the following guideline might be helpful to build a robust link. A proper frequency
deviation is linked to the frequency error between transmitter and receiver. The frequency error can be calculated
using the crystal tolerance parameters and the RF operating frequency: (ppm_tx+ppm_rx)*Frf/1E-6. For frequency
errors below 50 kHz, the deviation can be about the same as the frequency error. For frequency errors exceeding
50 kHz the frequency deviation can be set to about 0.75 times the frequency error. It is advised to position the
modulation index (=2*freq_dev/data_rate) into a range between 1 and 100 for Packet Handling mode and 2 to 100
for direct mode (non-standard preamble). For example, when in Packet Handling mode and the frequency error is
smaller than data_rate/2, the frequency deviation is set to about data_rate/2. When the frequency error exceeds
100xdata_rate/2, the frequency deviation is preferred to be set to 100xdata_rate/2.
4.2.4. Data Rate
The Si4355 can be set to communicate at between 1 to 500 kbps in (G)FSK mode and between 0.5 to 120 kbps in
OOK mode. Higher data rates allow for faster data transfer while lower data rates result in improved sensitivity and
range performance.
4.2.5. Channel Bandwidth
The channel bandwidth sets the bandwidth for the receiver. Since the receiver bandwidth is directly proportional to
the noise allowed in the system, this will normally be set as low as possible. The specific channel bandwidth used
will usually be determined based upon the precision of the oscillator and the frequency deviation of the transmitted
signal. The EZConfig setup can provide the recommended channel bandwidth based upon these two parameters
to help optimize the system.
4.2.6. Preamble Length
A preamble is a defined simple bit sequence used to notify the receiver that a data transmission is imminent. The
length of this preamble will normally be set as short as possible to minimize power while still insuring that it will be
reliably detected given the receiver characteristics, such as duty cycling and packet error rate performance. The
Si4355 allows the preamble length to be set between 3 to 255 bytes in length with a default length of 4 bytes. The
preamble pattern for the Si4355 will always be 55h with a first bit of "0" if the packet handler capability is used.
4.2.7. Sync Word Length and Pattern
The sync word follows the preamble in the packet structure and is used to identify the start of the payload data and
to synchronize the receiver to the transmitted bit stream. The Si4355 allows for sync word lengths of 1 to 4 bytes
and the specific pattern can be set within the EZConfig program. The default is a 2 byte length 2d d4 pattern.
4.2.8. Cyclic Redundancy Check (CRC)
CRC is used to verify that no errors have occurred during transmission and the received packet has exactly the
same data as it did when transmitted. If this function is enabled in the Si4355, the last byte of transmitted data must
include the CRC generated by the transmitter. The Si4355 then performs a CRC calculation on the received packet
and compares that to the transmitted CRC. If these two values are the same, the Si4355 will set an interrupt
indicating a valid packet has been received and is waiting in the Rx FIFO. If these two CRC values differ, the
Si4355 will flag an interrupt indicating that a packet error occurred. The Si4355 uses CRC(16)-IBM: x16+x15+x2+1
with a seed of 0xFFFF.
Rev 1.0
17
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SI4388DY-T1-GE3
MOSFET DUAL N-CH 30V 8-SOIC
SI4390DY-T1-GE3
MOSFET N-CH 30V 8.5A 8SOIC
SI4396DY-T1-GE3
MOSFET N-CH D-S 30V 8-SOIC
SI4398DY-T1-GE3
MOSFET N-CH 20V 19A 8-SOIC
SI4404DY-T1-GE3
MOSFET N-CH D-S 30V 8-SOIC
SI4406DY-T1-GE3
MOSFET N-CH D-S 30V 8-SOIC
SI4410DY
MOSFET N-CH 30V 10A 8-SOIC
SI4411DY-T1-GE3
MOSFET P-CH D-S 30V 8-SOIC
相关代理商/技术参数
Si4355-B1A-FMR
功能描述:射频接收器 Si4355 EZRadio Rcvr
RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
SI4355-B1A-GM
制造商:Silicon Laboratories Inc 功能描述:SI4355 EZRADIO RECEIVER - Bulk
SI4356ADY
制造商:VAISH 制造商全称:VAISH 功能描述:N-Channel 30-V (D-S) MOSFET
Si4356ADY-T1-E3
功能描述:MOSFET 30V 26A 6.5W RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4356ADY-T1-GE3
功能描述:MOSFET 30V 26A 6.5W 5.5mohm @ 10V RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4356-B1A-FM
制造商:Silicon Laboratories Inc 功能描述:SI4356 STANDALONE SUB-GHZ RECE 制造商:Silicon Laboratories Inc 功能描述:SI4356 STANDALONE SUB-GHZ RECEIVER - Rail/Tube 制造商:Silicon Laboratories Inc 功能描述:IC RX SUB-GHZ STAND ALONE QFN 制造商:Silicon Laboratories Inc 功能描述:RF Receiver Si4356 Standalone Sub-GHz Receiver
SI4356-B1A-FMR
制造商:Silicon Laboratories Inc 功能描述:SI4356 STANDALONE SUB-GHZ RECE 制造商:Silicon Laboratories Inc 功能描述:RECEIVER RF CI SMD - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:RF Receiver Si4356 Standalone Sub-GHz Receiver
SI4356DY
制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:N-Channel 30-V MOSFET